Monday, July 6, 2015

Treasure chest with curved lid part 4, working on the bottom and finding a couple of design flaws

The glue had dried and it did indeed still work even though I passed the "best before" date written on the container.

The panel was not flat, but I guess it comes pretty natural after glueing up to cupped boards. At first I traversed it with the scrub plane, and then when it was flattish I started going with the grain.
After a bit of workout, it was nice and flat.

I dry assembled the carcase of the chest, and after checking that it was square, I traced the outline of the bottom onto the bottom panel.

According to my sketch it will look good if the bottom is protruding on all sides, just something like 1/4". This could technically be achieved by adding a small piece of moulding, but I didn't bring any moulding planes with me, so I had to think of another way to make this small detail.

The plan was to make a groove near the bottom of the carcase, to house the bottom, That is pretty traditional.
In order for the lower part of the bottom to protrude I had to make a rabbet along all the sides of the bottom.
Then on the remaining full thickness part of the bottom I had to make a groove, so I would end up with a thin piece of bottom that would fit into the grooves of the carcase sides.
In my mind this worked very well.

Design flaw No 1
I normally stick to the grooving before dovetailing, but I didn't do it this time because my original idea was to simply make a rabbet and then nail the bottom on.
Due to my interlocking groove idea, I had to make a set of grooves without messing up the dovetails, so I wouldn't get a groove that would be visible from the outside of the chest.
On the sides it worked really well, since I just cleared the tails.
On the end boards I found myself needing to make a stopped groove - as in stopped in both ends. I tried using my grooving plane, but it pretty quickly became evident, that this tool was not intended for making that kind of grooves.
My solution was to use a utility knife for defining the sides of the groove. I adjusted the iron of the grooving plane so it protruded a little less than 1/4" (5 mm to be exact). That made it possible for me to use the grooving plane as sort of a router plane.
It took a bit more time than I had expected, but the grooves turned out well.

Design flaw No 2
If you need to make a groove on the side of your rabbet, be sure not to make the rabbet wider than your grooving plane can handle..
This flaw was discovered after I had finished planing the almost 3/4" wide rabbet all the way around the bottom.
I think that I might be able to tackle it sort of the same way I did with the stopped grooves. But I decided to call it a day and not risking to mess up things by keeping on working too late.

After imposing those additional challenges on myself, I would like to explain why I changed the design in the first place:
I wanted to make sure that there would be no crack between the sides and the bottom if it should move with the seasons. Therefore I got the idea of housing the bottom in a groove.
And making one bottom, and then glueing on a decorative bottom seemed like an idea that required too much work. Guess I was wrong about that.

Flattening the bottom.

A stopped groove.
Note the protrusion of the iron on the plane.

The bottom with rabbets.


2 comments:

  1. Jonas
    I really enjoy reading your posts and your problems solving. To me that's the fun part of woodworking, solving problems on the fly, for I always work without any real plans, just doodles :-)
    Bob

    ReplyDelete
    Replies
    1. Hi Bob

      Thanks for the kind words.
      I am glad to know that I am not alone on this one :-)
      The process of making something out here is definitely more important than the outcome, since it is basically a way of recharging my own batteries. Off course it is nice when things go smoothly, but it is also challenging to be able to overcome a problem.
      I would like to work to a "real" plan sometime, but I think it will have to be while I am at home, because out here I am very limited in materials and tools etc. So it makes more sense to make up the plan as I go along out here.
      Brgds
      Jonas

      Delete